Ground Segment

This chapter describes the ground segment of the mission. It is composed of two ground stations (one at the INPE-RN installations and the other at the SpaceLab installations) and many data collection platforms (PCD, or “Plataforma de Coleta de Dados”), installed at a variety of locations on the Brazilian territory.

The control of the mission and the reception of the collected data will be performed mainly at these two ground stations, but if necessary, other stations can execute this task. Any station in the world can use the amateur radio link since having the required equipment to it.

UFSC Ground Station

The UFSC ground station is currently being developed and prepared for this mission. This section presents the project of this station. A general block diagram can be seen in Fig. 43.

Block diagram of the ground segment (UFSC ground station).

Fig. 43 Block diagram of the ground segment (UFSC ground station).

In the following sections, a description of the main components of the station will be presented.

Hardware

This part describes the hardware side of the UFSC ground station and details the main peripherals that will be used in this project. Most of the components described here are represented in Fig. 43.

Antennas

There are two antennas in the ground station: One for VHF and one for the UHF band. The main characteristics of these antennas can be seen in Table 20

Table 20 Main characteristics of the ground segment antennas.

Characteristic

VHF Antenna

UHF Antenna

Unit

Brand

M²

Cushcraft

Model

2MCP14

A719B

Type

Yagi

Yagi

Number of elements

14

19

Frequency range

143-148

430-450

MHz

Gain

12.34

15.5

dBi

Power rating

1500

2000

W

Boom length

3.2

4.1

m

Longest element

1.02

0.34

m

Weight

2.72

2.55

kg

More information about the VHF and UHF antennas can be found in [11] and [1] respectively.

Surge Protector

Two surge protectors will be used to protect the ground station electronics of possible atmospheric discharges in the outside components (one for each antenna). The gas surge protectors safely discharge/deflect up to 5000 A of peak current to earth without causing damage to an independent ground. This device is installed near the antennas, in cascade with the RF cables.

For this project, the model MFJ-270N will be used, and a picture of it can be seen in Fig. 44.

MFJ-270N surge protector.

Fig. 44 MFJ-270N surge protector.

Rotators

Both antennas (VHF and UHF) track the satellite through a two axis rotator (azimuth and elevation). The used model is the Yaesu G-5500, which provides 450° azimuth and 180° elevation control of medium and large size unidirectional satellite antenna arrays under remote control from station operation position.

A picture of the G-5500 rotator (and controller) can be seen in Fig. 45; the main characteristics can be found in Table 21.

Yaesu G-5500 rotator and controller.

Fig. 45 Yaesu G-5500 rotator and controller.

Table 21 Main characteristics of antennas’ rotators.

Characteristic

Value

Unit

Brand

Yaesu

Model

G-5500

Voltage requirement

110-120 or 200-240

\(V_{AC}\)

Motor voltage

24

\(V_{AC}\)

Rotation time (elevation, 180°)

67

s

Rotation time (azimuth, 360°)

58

s

Maximum continuous operation

5

min

Rotation torque (elevation)

14

kg-m

Rotation torque (azimuth)

6

kg-m

Braking torque (elevation and azimuth)

40

kg-m

Vertical load

200

kg

Pointing accuracy

± 4

%

Wind surface area

1

\(m^{2}\)

Weight (rotator)

9

kg

Weight (controller)

3

kg

More information about the ground station rotator can be found in [4].

Amplifiers

There are two dedicated amplifiers in the UFSC ground station: one power amplifier (PA) for transmitting telecommands with a high power signal, and a low noise amplifier (LNA), for amplify the received signals from the satellite. Both are presented next.

Power Amplifier

The power amplifier is used to add a gain to the generated signals of the transmitter. The used model is the Mini-Circuits ZHL-50W-52-S+ [23]. A picture of this power amplifier can be seen in Fig. 46, the main characteristics are available in Table 22.

Mini-Circuits ZHL-50W-52-S+ power amplifier.

Fig. 46 Mini-Circuits ZHL-50W-52-S+ power amplifier.

Table 22 Main characteristics of the ZHL-50W-52-S+ power amplifier.

Characteristic

Value

Unit

Brand

Mini-Circuits

Model

ZHL-50W-52-S+

Frequency range

50-500

MHz

Gain

47-52

dB

Noise figure

4.5-7.0

dB

DC supply voltage

24-25

V

Max. supply current

9.3

A

Low Noise Amplifiers

As LNA, the model ZFL-500LN+ from Mini-Circuits [24] is being used. This amplifier will be used just after the antennas to add a gain to the incoming telemetry signals transmitted by the satellite. A picture of the low noise amplifier can be seen in Fig. 47, the main characteristics are available in Table 23.

Mini-Circuits ZFL-500LN+ low noise amplifier.

Fig. 47 Mini-Circuits ZFL-500LN+ low noise amplifier.

Table 23 Main characteristics of the ZFL-500LN+ low noise amplifier.

Characteristic

Value

Unit

Brand

Mini-Circuits

Model

ZFL-500LN+

Frequency range

0.1-500

MHz

Gain

24-28

dB

DC supply voltage

15

V

Max. supply current

60

mA

Radios

Besides the SDR solution presented in the block diagram of the Fig. 43, there is also a amateur radio transceiver with a standalone solution for the amateur radio link with the satellite. The used model is the Icom IC-9700 [16], that is an RF direct sampling receiver for 2 m and 70 cm. The IF receiver consists of a single down conversion for 23 cm that is between 311 and 371 MHz. The PA provides 100 W on 2 m, 75 W on 70 cm, and 10 W on 23 cm.

In addition to band-specific memory channels, the IC-9700 allows the band-specific receiver and transmitter settings. For transmission, users can adjust RF power, TX power Limit, Limit Power, and TX Delay by the band. Basic receiver settings, like the Noise Blanker, Noise Reduction, and others, can be tweaked by the band with a dynamic Notch and Filter setup by band/mode. A picture of the IC-9700 radio can be seen in Fig. 48.

Icom IC-9700 radio transceiver.

Fig. 48 Icom IC-9700 radio transceiver.

Software Defined Radio

As presented in Fig. 43, the ground segment also has an SDR (Software Defined Radio) as a transceiver. The used model is the USRP B210, from Ettus Research [3], a fully integrated, single-board SDR with continuous frequency coverage from 70 MHz to 6 GHz. It combines the AD9361 RFIC direct-conversion transceiver providing up to 56 MHz of real-time bandwidth, an open and reprogrammable Spartan6 FPGA, and USB 3.0 connectivity. Also, full support for the USRP Hardware Driver (UHD) software allows the use of the GNURadio framework. A picture of the USRP B210 SDR (with enclosure) can be seen in Fig. 49.

Ettus USRP B210 SDR.

Fig. 49 Ettus USRP B210 SDR.

Processing and Control

The ground station control room shall have two monitors and a dedicated computer alongside most of the previously presented hardware. It will work as a monitoring room with a nobreak to protect the equipment from power grid fluctuations.

The antennas and rotator will also be monitored with outside cameras. And the room will count with a server so that the transmission and decoding can be done remotely and at any time.

In the Fig. 50 can be seen a picture of the used server, and in Table 24 are presented the main characteristics of the it.

Table 24 Main characteristics of the Dell PowerEdge R240 server.

Characteristic

Value

Brand

Dell

Model

PowerEdge R240

Processor

Intel Xeon E-2244G 3.8 GHz 4C/8T

RAM Memory

16 GB DDR4 ECC

Storage

1 TB HD

Dell PowerEdge R240 server.

Fig. 50 Dell PowerEdge R240 server.

Satellite Tracking

To track the satellite and for orbit prediction, the GPredict software [27] will be used. Gpredict is a real-time satellite tracking and orbit prediction application. It can track many satellites and display their position and other data in lists, tables, maps, and polar plots (radar view). Gpredict can also predict the time of future passes for a satellite and provide detailed information about each pass. Gpredict is free software licensed under the GNU General Public License. A picture of the main window of GPredict can be seen in Fig. 51.

Main window of GPredict.

Fig. 51 Main window of GPredict.

Packet Transmission

The packet generation and transmission to GOLDS-UFSC satellite can be done with the SpaceLab-Transmitter software [20], which was written in Python with the interface developed using the GTK framework. It has a USRP Handler made with Ettus libraries to work with Ettus USRP B210 as shown in Fig. 49. The supported modulation is the Gaussian Minimum Shift Keying (GMSK). Furthermore, the software also has unit tests for the main modules and a logging system to record events such as an initialization or a successfully transmitted telecommand.

In the Fig. 52 is shown the product tree of the software, which contains its main elements of it, and in the Fig. 53 is shown the main window of it.

SpaceLab-Transmitter product tree.

Fig. 52 SpaceLab-Transmitter product tree.

Main window of the SpaceLab-Transmitter application.

Fig. 53 Main window of the SpaceLab-Transmitter application.

Packet Decoding

The packet decoding of GOLDS-UFSC satellites telemetry can be done using the SpaceLab-Decoder [19] software using a .wav file or through a real time reception. The decoded telemetry will appear in a dialog within the main window. The software was written in Python, and the interface was developed using GTK framework. Furthermore, the software also has unit tests for the main modules and a logging system to record events.

The Fig. 54 is showing the product tree of the software, which contains its main elements, and in the Fig. 55 is shown the main window of it.

SpaceLab-Decoder product tree.

Fig. 54 SpaceLab-Decoder product tree.

Main window of the SpaceLab-Decoder application.

Fig. 55 Main window of the SpaceLab-Decoder application.

EMMN Ground Station

The EMMN (Estação Multimissão de Natal in portuguese) ground station [29] was designed to operate in VHF, UHF and S-Band frequency bands, receiving payload and telemetry data and transmitting telecommands from and to satellites operating in low orbits.

The station’s radio frequency systems use Software Defined Radios (SDRs), which offer the flexibility to quickly reconfigure parameters such as modulation type, encoding, datarate, etc. Most commonly used modulation schemes and encoding methods are already implemented, and any customization requests can be requested.

The station performs autonomous tracking of several satellites according to a previous schedule and a scale of priorities. A Client-Server network design allows station users to send and receive data remotely.

A general block diagram of the EMMN hardware is available in Fig. 56.

General block diagram of the EMMN.

Fig. 56 General block diagram of the EMMN.

Table 25 EMMN specs.

Parameter

Value

Grid locator

HI24JD59CI

Coordinates

-5.835238, -35.209285

Altitude

51 m

Antennas

Yagi and parabolic

Bands

VHF, UHF and S-Band

Frequencies

144-146 MHz (VHF), 395-405 and 432-440 MHz (UHF) 2200-3300 MHz (S-Band)

Multimission station of Natal-RN.

Fig. 57 Multimission station of Natal-RN.

Data Collection Platforms

Data Collection Platforms (DCPs) are part of the Integrated System of Environmental Data (Sistema Integrado de Dados Ambientais, SINDA [32], in Portuguese), which collects the data and by satellites, it is retransmitted to be received in the ground station so that it can be sent to SINDA to be processed. The data is shown online sometime after the receiving. Examples of DCPs can be seen in Fig. 58.

Examples of data collection platforms (DCPs).

Fig. 58 Examples of data collection platforms (DCPs).

First data collection platform.

_images/pcd-2.jpg _images/pcd-3.jpg