Logo

Documentation

  • Introduction
  • Mission Management
  • Concept of Operations
  • Technical Budgets and Mission Analysis
  • Service Module Overview
  • Subsystems
  • Ground Segment
  • Test Plan and Procedures
  • Assembly, Integration and Test
  • Nomenclature
  • References

Appendix

  • Link Budget Calculation
    • Distance to Satellite at Horizon
    • Free-Space Path Loss
      • Beacon
      • Downlink/Uplink
      • Uplink (Payload)
    • Power at Receiver
      • Beacon
      • Downlink (UHF)
      • Uplink (UHF)
      • Uplink (Payload)
    • Signal-to-Noise-Ratio
      • Beacon
      • Downlink
      • Uplink
      • Uplink (Payload)
    • Link Margin
  • Telecommunication Packets
  • EDC Test Report
golds-ufsc
  • Link Budget Calculation
  • View page source

Link Budget Calculation

This appendix shows the link budget calculation of all the satellite links (including the radio links of the payloads). The method used was taken from [33] (section 13.3).

Distance to Satellite at Horizon

The distance to the satellite at the horizon (the maximum theoretical distance between the satellite and a ground station) can be calculated using (4).

(4)\[d = \sqrt{2\cdot R_{e}\cdot h + h^{2}}\]

Where:

  • \(R_{e}\) = Earth radius = 6378 km

  • \(h\) = Satellite altitude = 550 km

  • \(d\) = Distance to the satellite at the horizon

So, the distance to the satellite at the horizon is:

(5)\[d = \sqrt{2\cdot 6378\cdot 550 + 550^{2}} = \mathbf{2705\ km}\]

Free-Space Path Loss

The free-space path loss (\(FSPL\)) can be calculated using (6).

(6)\[FSPL = \left( \frac{4\pi d f}{c} \right)^{2}\]

Where:

  • \(d\) = Distance between the satellite and the ground station

  • \(f\) = Radiofrequency

  • \(c\) = Speed of light

The FSPL value in decibels can be calculated with (7).

(7)\[\begin{split}\begin{split} FSPL^{dB} & = 20\log\left(\frac{4\pi}{c}\right) + 20\log\left(d\right) + 20\log\left(f\right) \\ & = 32,45 + 20\log\left(\frac{d}{1\ km}\right) + 20\log\left(\frac{f}{1\ MHz}\right) \\ \end{split}\end{split}\]

The minimum distance between the satellite and a ground station is the satellite altitude, in this case: 600 km. The maximum distance is the distance at the horizon, defined by (5).

Beacon

Considering the frequency of the beacon as 437 MHz, the minimum and maximum FSBL is:

\[FSPL^{dB}_{min} = 32,45 + 20\log\left(\frac{550}{1\ km}\right) + 20\log\left(\frac{146}{1\ MHz}\right) = \mathbf{130,5\ dB}\]
\[FSPL^{dB}_{max} = 32,45 + 20\log\left(\frac{2705}{1\ km}\right) + 20\log\left(\frac{146}{1\ MHz}\right) = \mathbf{144,4\ dB}\]
\[\mathbf{130,5 \leq FSPL^{dB} \leq 144,4\ dB}\]

Downlink/Uplink

Considering the frequency of the downlink/uplink as 462,5 MHz, the minimum and maximum FSBL is:

\[FSPL^{dB}_{min} = 32,45 + 20\log\left(\frac{550}{1\ km}\right) + 20\log\left(\frac{450}{1\ MHz}\right) = \mathbf{140,3\ dB}\]
\[FSPL^{dB}_{max} = 32,45 + 20\log\left(\frac{2705}{1\ km}\right) + 20\log\left(\frac{450}{1\ MHz}\right) = \mathbf{154,2\ dB}\]
\[\mathbf{140,3 \leq FSPL^{dB} \leq 154,2\ dB}\]

Uplink (Payload)

Considering the frequency of the payload’s uplink is 401,635 MHz, the minimum and maximum FSBL is:

\[FSPL^{dB}_{min} = 32,45 + 20\log\left(\frac{550}{1\ km}\right) + 20\log\left(\frac{401,635}{1\ MHz}\right) = \mathbf{139,3\ dB}\]
\[FSPL^{dB}_{max} = 32,45 + 20\log\left(\frac{2705}{1\ km}\right) + 20\log\left(\frac{401,635}{1\ MHz}\right) = \mathbf{153,2\ dB}\]
\[\mathbf{139,3 \leq FSPL^{dB} \leq 153,2\ dB}\]

Power at Receiver

The power of the signal at the receiver can be estimated using (8).

(8)\[P_{r} = P_{t} + G_{t} + G_{r} - L_{p} - L_{s}\]

Where:

  • \(P_{r}\) = Power at the receiver

  • \(P_{t}\) = Transmitter power

  • \(G_{t}\) = Antenna gain of the transmitter

  • \(G_{r}\) = Antenna gain of the receiver

  • \(L_{p}\) = FSPL (Free-Space Path Loss)

  • \(L_{s}\) = Other losses in the system

Considering the worst scenario with the maximum possible distance between the satellite and a ground station, the power at the receiver for each link is calculated below.

Beacon

\[P_{r} = 30 + 0 + 12 - 144,4 - 5 = -107,4\ dBm\]
\[\mathbf{P_{r} \geq -107,4\ dBm}\]

Downlink (UHF)

\[P_{r} = 30 + 0 + 12 - 154,2 - 5 = -117,2\ dBm\]
\[\mathbf{P_{r} \geq -117,2\ dBm}\]

Uplink (UHF)

\[P_{r} = 44 + 12 + 0 - 154,2 - 5 = -103,2\ dBm\]
\[\mathbf{P_{r} \geq -103,2\ dBm}\]

Uplink (Payload)

\[P_{r} = 30 + 3 + 0 - 153,2 - 5 = -125,2\ dBm\]
\[\mathbf{P_{r} \geq -125,2\ dBm}\]

Signal-to-Noise-Ratio

The Signal-to-Noise-Ratio (SNR, Signal To Noise Ratio) of a transmitted signal at the receiver can be expressed using (9):

(9)\[SNR = \frac{E_{b}}{N_{0}} = \frac{P_{t}G_{t}G_{r}}{kT_{s}RL_{p}}\]

Where:

  • \(P_{t}\) = Transmitter power

  • \(G_{t}\) = Antenna gain of the transmitter

  • \(G_{r}\) = Receiver gain

  • \(k\) = Boltzmann’s constant (\(\cong 1,3806 \times 10^{-23}\ J/K\))

  • \(T_{s}\) = System noise temperature

  • \(R\) = Data rate in bits per second (bps)

  • \(L_{p}\) = Free-Space Path Loss (FSPL)

The system noise temperature (\(T_{s}\)) can be defined using (10).

(10)\[T_{s} = T_{ant} + T_{r}\]

with:

(11)\[T_{r} = \frac{T_{0}}{L_{r}} (F - L_{r})\]

and:

(12)\[F = 1 + \frac{T_{r}}{T_{0}}\]

Combining Equations (10), (11) and (12):

(13)\[T_{s} = T_{ant} + \left( \frac{T_{0}(1 - L_{r})}{L_{r}} \right) + \left( \frac{T_{0} (F - 1)}{L_{r}} \right)\]

Where:

  • \(T_{ant}\) = Antenna noise temperature

  • \(T_{0}\) = Reference temperature (usually 290 K)

  • \(L_{r}\) = Line loss between the antenna and the receiver

  • \(F\) = Noise figure of the receiver

  • \(T_{r}\) = Noise temperature of the receiver

The SNR value in decibels can be calculated using the (14):

(14)\[\begin{split}\begin{split} SNR^{dB} & = 10\log_{10}\left( \frac{E_{b}}{N_{0}} \right) = 10\log_{10} \left( \frac{P_{t}G_{t}G_{r}}{kT_{s}RL_{p}} \right) \\ & = P_{t}^{dBm} - 30 + G_{t}^{dB} + G_{r}^{dB} - L_{p}^{dB} - 10\log k - 10\log T_{s} - 10\log R \end{split}\end{split}\]

Considering other losses in the system (\(L_{s}\)) (cable and connection losses as an example), the (14) can be corrected as presented in (15).

(15)\[SNR^{dB} = P_{t}^{dBm} - 30 + G_{t}^{dB} + G_{r}^{dB} - L_{p}^{dB} - L_{s}^{dB} - 10\log k - 10\log T_{s} - 10\log R\]

Beacon

Using Equations (15) and (10), with:

  • \(P_{t} = 30\ dBm\)

  • \(G_{t} = 0\ dBi\)

  • \(G_{r} = 12\ dBi\)

  • \(L_{p} = 144,4\ dB\)

  • \(L_{s} = 5\ dB\)

  • \(R = 1200\ bps\)

  • \(T_{0} = 290\ K\)

  • \(T_{r} = 290\ K\)

  • \(T_{ant} = 300\ K\)

  • \(F = 2\ dB\)

  • \(L_{r} = 0,89\ (0,5\ dB)\)

\[T_{s} = 300 + \left( \frac{290 (1 - 0,89)}{0,89} \right) + \left( \frac{290 (2 - 1)}{0,89} \right) = 661,7\ K\]
\[SNR^{dB} = 30 - 30 + 0 + 12 - 144,4 - 5 + 228,6 - 28,21 - 30,79 = 32,22\ dB\]
\[\mathbf{SNR^{dB} \geq 32,22\ dB}\]

Downlink

Using Equations (15) and (10), with:

  • \(P_{t} = 30\ dBm\)

  • \(G_{t} = 0\ dBi\)

  • \(G_{r} = 12\ dBi\)

  • \(L_{p} = 154,2\ dB\)

  • \(L_{s} = 5\ dB\)

  • \(R = 9600\ bps\)

  • \(T_{0} = 290\ K\)

  • \(T_{r} = 290\ K\)

  • \(T_{ant} = 300\ K\)

  • \(F = 2\ dB\)

  • \(L_{r} = 0,89\ (0,5\ dB)\)

\[SNR^{dB} = 30 - 30 + 0 + 12 - 154,2 - 5 + 228,6 - 28,21 - 39,82 = 13,41\ dB\]
\[\mathbf{SNR^{dB} \geq 13,41\ dB}\]

Uplink

Using Equations (15) and (10), with:

  • \(P_{t} = 44\ dBm\)

  • \(G_{t} = 12\ dBi\)

  • \(G_{r} = 0\ dBi\)

  • \(L_{p} = 154,2\ dB\)

  • \(L_{s} = 5\ dB\)

  • \(R = 9600\ bps\)

  • \(T_{0} = 290\ K\)

  • \(T_{r} = 290\ K\)

  • \(T_{ant} = 300\ K\)

  • \(F = 2\ dB\)

  • \(L_{r} = 0,89\ (0,5\ dB)\)

\[SNR^{dB} = 44 - 30 + 12 + 0 - 154,2 - 5 + 228,6 - 28,21 - 39,82 = 27,41\ dB\]
\[\mathbf{SNR^{dB} \geq 27,41\ dB}\]

Uplink (Payload)

Using Equations (15) and (10), with:

  • \(P_{t} = 30\ dBm\)

  • \(G_{t} = 3\ dBi\)

  • \(G_{r} = 0\ dBi\)

  • \(L_{p} = 153,2\ dB\)

  • \(L_{s} = 5\ dB\)

  • \(R = 400\ bps\)

  • \(T_{0} = 290\ K\)

  • \(T_{r} = 290\ K\)

  • \(T_{ant} = 300\ K\)

  • \(F = 2\ dB\)

  • \(L_{r} = 0,89\ (0,5\ dB)\)

\[SNR^{dB} = 30 - 30 + 3 + 0 - 153,2 - 5 + 228,6 - 28,21 - 26,02 = 19,17\ dB\]
\[\mathbf{SNR^{dB} \geq 19,17\ dB}\]

Link Margin

From [33], the minimum SNR value at the received considering a \(10^{-5}\) bit error rate is:

  • Beacon: \(SNR^{dB} \geq 9,6\ dB\)

  • Downlink/Uplink: \(SNR^{dB} \geq 9,6\ dB\)

  • Uplink (payload): \(SNR^{dB} \geq 9,6\ dB\)

And considering the link margin as the SNR of the link minus the SNR threshold for a given bit error, the link margin of the radio links of the satellite are:

  • Beacon: \(32,22 - 9,6 = \mathbf{22,62\ dB}\)

  • Downlink: \(13,41 - 9,6 = \mathbf{3,812\ dB}\)

  • Uplink: \(27,41 - 9,6 = \mathbf{17,81\ dB}\)

  • Uplink (payload): \(19,17 - 9,6 = \mathbf{9,57\ dB}\)

Previous Next

© Copyright The GOLDS-UFSC Contributors.

Built with Sphinx using a theme provided by Read the Docs.